Ø12 mm~Ø12.7 mm(Ø1/2インチ)ポスト用スリップオン式カラー


  • Slip-On Collars for Ø1/2" Posts
  • Restrict Post Height or Rotation Orientation
  • Exchange Components While Maintaining Alignment

KS2 Ø2" Mirror Mount on Ø1/2" Post with RMC Position-Maintaining Collar

R2

0.44'' (11.2 mm) Thick with Height Adjustment

R2T

Thin, 0.23" (5.7 mm) Thick Design

RMC

Two-Piece Design Maintains Vertical and Rotational Position of a Ø1/2'' Post

Related Items


Please Wait

特長

  • ポストの高さまたは回転方向を保持するカラー
  • ポスト用スリップオン式カラーR2/Mは、止めネジ(セットスクリュ)による精密な高さ調整が可能
  • ポストカラーRMC は、高さならびに回転方向を一定に保持

このページでご紹介しているスリップオン式カラーは、セットアップ内でポストに取り付けたオプトメカニクス部品を取外す必要がある場合に、一度設定した高さを保持できるように設計されています。  2つの部品で構成されているポストカラーRMCは、ポストの高さ設定に加えてポストの回転方向を一定に保持することができます。 カラーはポストに取り付けられたレンズなどの部品を交換する際に役立ち、レンズの高さをシステムの光軸にアライメントしたままにしておくことができます。 また他のオプションとして、ポストカラーR2/MまたはR2Tを当社の 回転止めアダプタと一緒に用いて、回転方向を一定に保つこともできます。


Posted Comments:
jdemuth  (posted 2017-07-11 23:29:04.377)
I wanted a compact vertical post adjuster, so I took the RMC bottom, (while it is not quite right for this application, it could be adjusted easily to work) and removed the ball bearing, leaving a divot and mounted it to a post holder. I then mounted a APM03 to the post, and viola! I had an extremely compact vertical adjustment mechanism. Ideally you (Thorlabs) could slightly tweak the RMC bottom to better mate with the APM03, this would be even better, and extremely useful!!! best, James
tfrisch  (posted 2017-08-07 11:37:24.0)
Hello, thank you for contacting Thorlabs. It sounds like you are describing an alternative to APM02 with a divot. I can post this in our internal engineering forum and reach out to you directly to discuss your application.
cbrideau  (posted 2015-03-09 14:02:53.253)
You should offer extras of the upper portion of the RMC collar for purchase. That way you could have several different mounts preset via the upper collar, ready to be swapped out and dropped on to the lower collar on a fixed post holder.
cdaly  (posted 2015-03-26 10:16:03.0)
Response from Chris at Thorlabs: Thank you for your feedback. We will look into either adding these as new separate components, or possibly making the change to the R2T so that the location groove is standard.
cdaly  (posted 2013-03-06 10:40:00.0)
Response from Chris at Thorlabs: Thank you for using our web feedback. While this is a point at which the R2 can in fact break, this is under far more stress than the product is intended for. The collar should be sufficiently tight with a quarter turn of a hex key past hand tight. The setscrew is used for initial final positioning. Once the correct height is achieved, the post holder should be used to secure the height of the post. Once this is tight, the set screw can be retracted and the collar readjusted so a repeatable height can occur if the post is removed and reinserted into the post holder. However, if greater torque is required without the small screw, I would recommend that you consider the R2T. It is thinner profile, but has no setscrew and can handle much more toque. You'll need to use a ball driver or hex key to tighten this down as it uses an 8-32 set screw to clamp to the post, rather than the 1/4-20 thumbscrew in the R2.
Thorlabs  (posted 2011-01-19 09:33:18.0)
Response from Javier at Thorlabs to graum: Thank you very much for your feedback. We actually offer a few other components that are designed for mounting 1/2" posts parallel to the optical table and, at the same time, are attached to perpendicularly mounted posts. Please visit the following link: http://www.thorlabs.com/NewGroupPage9.cfm?ObjectGroup_ID=1985
graum  (posted 2011-01-18 14:03:49.0)
I use a lot of R2 post collars with my 1/2" posts in lab. One thing Ive found useful is to give them an additional 4-40 tap. With this I can screw on a 1/2" post to the side, and then use this post-collar assembly to mount a post parallel to my table off of a post already mounted perpendicular to the table. I think this would be a useful addition to anyone who wants to use these posts. It would certainly increase their value to my lab.
Back to Top

ポスト用スリップオン式カラー

R2 with Post
Click to Enlarge
垂直方向の止めネジでポストの高さの精密調整が可能
  • 厚さ11.2 mm
  • 垂直方向に取付けM3 x 0.5止めネジ(セットスクリュ)付き
  • 5個入りパックもご用意

スリップオン式カラーR2/Mは、Ø12 mm~Ø12.7 mm(Ø1/2インチ)ポストにつまみネジで固定できます。このカラーをポストホルダの上部の位置にくるようにポストに装着すれば、取り付けた部品の高さを一定に保ったままポストを回転させることができます。 R2/MにはM3 x 0.5止めネジも付いています。この調整ネジを1.3 mm六角レンチで調整することで、ポストやポストホルダを動かさずに、約6.4 mmの高さ調整が可能です(右の写真参照)。 また、R2/Mと回転止めアダプタTRK05を一緒に使用してポストの回転を制限することもできます。

+1 数量 資料 型番 - インチ規格 定価(税抜) 出荷予定日
R2 Support Documentation
R2スリップオン式カラー、Ø1/2インチポスト用 (インチ規格)
¥815
7-10 Days
R2-P5 Support Documentation
R2-P5Customer Inspired! スリップオン式カラー、Ø1/2インチポスト用、5個入り (インチ規格)
¥3,891
Today
+1 数量 資料 型番 - ミリ規格 定価(税抜) 出荷予定日
R2/M Support Documentation
R2/Mスリップオン式カラー、Ø12 mm~Ø12.7 mmポスト用 (ミリ規格)
¥815
Today
R2/M-P5 Support Documentation
R2/M-P5Customer Inspired! スリップオン式カラー、Ø12 mm~Ø12.7 mmポスト用、5個入り (ミリ規格)
¥3,891
Today
Back to Top

ポスト用薄型スリップオン式カラーのセット

R2T
Click to Enlarge
先端が真ちゅう製の#8-32ネジを用いてカラーR2Tをポストに固定。
R2T with Post
Click to Enlarge
ポストホルダに取り付けたポストの垂直位置をカラーR2Tでマーキング。
  • 厚さ5.7 mm
  • 部品間隔の狭いセットアップに取付けが簡単な薄型設計
  • 5個入りパックで販売

R2Tは、上に掲載されているポスト用カラーR2/Mの薄型タイプで、付属の先端が真ちゅう製の#8-32止めネジでØ12 mm~Ø12.7 mm(Ø1/2インチ)のポストに固定できます。 このカラーをポストホルダの上部の位置でポストに装着すれば、取り付けた部品の高さを一定に保ったままポストを回転させたり外したりできます。 また、厚さがわずか5.7 mmなので、ポスト上であまり場所をとらず、ポストホルダに近い高さに部品を取り付けることができます。

R2Tと回転止めアダプタTRK05を一緒に使用してポストの回転を制限することもできます。 また、各R2Tには左図にあるように小さな溝が付いており、位置保持用ポストカラーRMC(下記参照)を使用しているセットアップ内で、追加のポスト用カラーとして使用することも可能です。

+1 数量 資料 型番 - ユニバーサル規格 定価(税抜) 出荷予定日
R2T Support Documentation
R2T薄型スリップオン式カラー、Ø12 mm~Ø1/2インチ(Ø1/2インチ)ポスト用、5個入り
¥5,818
Today
Back to Top

位置保持用ポストカラー


Click for Details
高さと回転方向を一定に保持できるポストカラーRMC

位置保持用ポストカラーの使用方法
  • 2つの部品からなるポストカラーで高さならびに回転方向を一定に保持
  • スチール製のボールとV型溝により≤0.5°の角度再現性
  • 高さを0.3 mm以内に維持

位置保持用ポストカラーRMCを使用することで、セットアップ内で一度設定したØ12 mm~Ø12.7 mm(Ø1/2インチ)ポストならびにポストホルダの高さと回転方向を一定に保持できます。カラーは、刻印が施された厚さ11.9 mmのポストホルダーカラーおよびこれより薄い厚さ5.7 mmのポストカラーの2つの部品で構成されています。スチール製のボールとこれに対応するV型溝が、≤0.5°の角度再現性を可能にしています。

RMCを使用するには、右の動画のようにポストホルダーカラーをØ12 mm~Ø12.7 mmポスト用ホルダの上に装着し、2 mm六角レンチでナイロンチップ付き#8-32止めネジ(セットスクリュ)を締めて位置を固定します。次にポストカラーのV型溝をポストホルダーカラーか ら突き出ているスチール製ボールにはめ込んで、ポストの高さを設定します(右の写真参照)。そして先端が真ちゅう製の#8-32止めネジを2 mm六角レンチで締めてポストカラーをポストに固定します。組立後でも、僅かながら回転方向の調整が可能で、下側のカラーの止めネジを緩めて回転することができます。

ポストカラーRMCを使用することで、ポストに取り付けられたオプトメカニクス部品を、その高さと回転方向を保持したまま素早く交換できます。その際、交換する部品には高さの設定されたポストカラーが装着されている必要があります。最良の結果を得るためには、止めネジがバネ式つまみネジの反対側にくるようにポストホルダーカラーを設置してください(右の写真参照)。下側のカラーの回転位置を調整する際には、ポストホルダのつまみ ネジからポストに予荷重がかかるようにしてください。これにより、調整する間も、ポストホルダとポスト間の2線接触を維持することができます。

+1 数量 資料 型番 - ユニバーサル規格 定価(税抜) 出荷予定日
RMC Support Documentation
RMC位置保持用ポストカラー、Ø12 mm~Ø12.7 mm(Ø1/2インチ)ポストおよびポストホルダ用
¥4,148
Today