高濃度エルビウム添加ファイバー、SMおよびLMA


  • Erbium-Doped Fiber for Fiber Amplifiers and Lasers
  • 1530 - 1610 nm Emission (C & L Bands)
  • 980 nm and 1480 nm Pump Wavelengths
  • Core-Pumped Single Mode or Large Mode Area Fibers Available

M12-980-125

ER30-4/125

Related Items


Please Wait
Item #TypePeak Core
Absorption
Pump
Type
MFD
(at 1550 nm)
Cladding
Diameter
ER30-4/125SMa30.0 ± 3.0 dB/mcCore6.5 ± 0.5 μm125 ± 2 μm
ER110-4/125110.0 ± 10.0 dB/mc
ER16-8/125LMAb16.0 ± 3.0 dB/mc9.5 ± 0.8 μm
ER80-8/12580.0 ± 8.0 dB/mc
M12-980-125SMa11.0 - 13.0 dB/md
16.0 - 20.0 dB/me
5.7 - 6.6 µm125 ± 1 μm
  • シングルモード
  • ラージモードエリア
  • 1530 nmにて測定
  • 980 nmにて測定
  • 1531 nmにて測定
Custom Fiber Patch Cables

特長

  • 発光波長域1530~1610 nm用エルビウム添加ファイバ
  • コア励起シングルモード(SM)とラージモードエリア(LMA)ファイバをご用意
  • クラッド径は、業界標準規格のØ125 µmで、取扱いや接続、終端処理が容易

当社では2つの製品シリーズのエルビウム添加アクティブファイバをご用意しております。 エルビウム添加ファイバLiekki®*は、シングルモード(SM)とラージモードエリア(LMA)の2タイプがあり、CバンドまたはLバンド(それぞれ1530~1565 nmと1565~1625 nm)出力用で、励起波長は980 nmまたは1480 nmです。 MetroGainエルビウム添加シングルモードファイバはLバンドでの出力用に設計されており、デバイス長を短くするため高ドーパント濃度となっています。

当社ではエルビウム添加偏波保持ファイバもご用意しております。

*Liekki®はnLIGHT社の登録商標です。

Active Fibers Selection Guide
Ytterbium-Doped SM and LMAYtterbium-Doped PMErbium-Doped SM and LMAErbium-Doped PM

Liekki エルビウム添加SM&LMAアクティブファイバ

Item #ER30-4/125ER110-4/125ER16-8/125ER80-8/125
Peak Core Absorption @ 1530 nm30.0 ± 3.0 dB/m110.0 ± 10.0 dB/m16.0 ± 3.0 dB/m80.0 ± 8.0 dB/m
Mode Field Diameter (MFD) @ 1550 nm6.5 ± 0.5 μm6.5 ± 0.5 μm9.5 ± 0.8 μm9.5 ± 0.8 μm
Numerical Aperture (NA, Nominal)0.20.20.130.13
Cut-Off Wavelength890 ± 90 nm890 ± 90 nm1250 ± 150 nm1250 ± 150 nm
Cladding Diameter125 ± 2 μm
Cladding GeometryRound
Coating (Second Cladding) Diameter245 ± 15 μm
Coating MaterialDual-Coated High-Index Acrylate
Core Concentricity Error≤ 0.7 μm
Proof Test≥ 100 kpsi
Core IndexProprietarya
Cladding IndexProprietarya
  • この仕様については開示されておりませんのでご了承ください。

Fibercore社MetroGainエルビウム添加SMファイバ

Item #M12-980-125
MFD (Nominal)5.7 - 6.6 µm at 1550 nm
Emission WavelengthL-Band
(1565 - 1625 nm)
Core Absorption @ 980 nm11.0 - 13.0 dB/m
Core Absorption @ 1531 nm16.0 - 20.0 dB/m
Core Numerical Aperture (NA, Nominal)0.21 - 0.24
Cut-Off Wavelength900 - 970 nm
Cladding Diameter125 ± 1 μm
Cladding GeometryRound
Coating Diameter (Nominal)245 ± 15 μm
Coating MaterialDual Acrylate
Background Loss< 20 dB/km
Core Concentricity Error≤ 0.5 μm
Proof Test1% (100 kpsi)
Core IndexProprietarya
Cladding IndexProprietarya
  • この仕様については開示されておりませんのでご了承ください。

高濃度エルビウム添加ファイバの吸収

群遅延、色分散、群遅延時間差の試験は、エルビウム添加ファイバER30-4/125(長さ約5 m)とER80-8/125(長さ約1 m)で行われました。試験結果は下記をご参照ください。

群遅延

下のグラフは、ER30-4/125とER80-8/125のエルビウム添加ファイバを使用した時に、3種類の異なる励起光出力における、波長と群遅延(GD)の関係を示しています。 群遅延とは、一定の光路長さにおいて、信号中の情報(変調波形の任意の点)が伝達するのに必要な時間のことです。

Group Delay for ER30
Group Delay for ER80

 

色分散

下のグラフは、ER30-4/125とER80-8/125のエルビウム添加ファイバを使用した時に、3種類の異なる励起光出力における、波長と色分散(CD)の関係を示しています。 色分散とは、群遅延と波長の関係を表したグラフにおける局所勾配です。

Chromatic Dispersion for ER30
Chromatic Dispersion for ER80

 

群遅延時間差

下のグラフは、ER30-4/125とER80-8/125のエルビウム添加ファイバを使用した時に、3種類の異なる励起出力における、波長と群遅延時間差(DGD)の関係を示しています。 群遅延時間差とは、あらゆる偏光状態での群遅延の最大バラツキです。

Differential group delay for ER30
Differential Group Delay for ER80

Active Optical Fiber Publications and Further Reading

As an emerging field of research, many advancements in doped fiber laser and amplifier construction are being made. The following publications contain information that may be helpful in the construction of fiber lasers and amplifiers.

2012

 

Bryce Samson, George Oulundsen, Adrian Carter, and Steven R. Bowman, "OPTICAL FIBER FABRICATION: Holmium-doped silica fiber designs extend fiber lasers beyond 2 µm," Laser Focus World, August 1, 2012

2011

 

Jianwu Ding, Bryce Samson, Adrian Carter, Chiachi Wang, Kanishka Tankala, "A Monolithic Thulium Doped Single Mode Fiber Laser with 1.5ns Pulsewidth and 8kW Peak Power," Proc. SPIE 7914, Fiber Lasers VIII: Technology, Systems, and Applications, 79140X (February 10, 2011); doi:10.1117/12.876867

2010

 

Timothy S. McComb, Pankaj Kadwani, R. Andrew Sims, Lawrence Shah, Christina C. C. Willis, Gavin Frith, Vikas Sudesh, Bryce Samson, Martin Richardson, "Amplification of Picosecond Pulses Generated in a Carbon Nanotube Modelocked Thulium Fiber Laser," in Lasers, Sources and Related Photonic Devices, OSA Technical Digest Series (CD) (Optical Society of America, 2010), paper AMB10.

G. Frith, A. Carter, B. Samson, J. Faroni, K Farley, K Tankala and G. E. Town, "Mitigation of photodegradation in 790nm-pumped Tm-doped fibers," Proc. SPIE 7580, Fiber Lasers VII: Technology, Systems, and Applications, 75800A (February 17, 2010); doi:10.1117/12.846230

Thomas Ehrenreich, Ryan Laveille, Imtiaz Majid, and Kanishka Tankala, Glen Rines, Peter Moulton "1-kW All-Glass Tm:fiber Laser," SPIE Photonics West 2010: LASE Presentation, Session 16: Late-Breaking News, January 29, 2010

2009

 

Gavin Frith, Adrian Carter, Bryce Samson, and Graham Town, "Design considerations for short-wavelength operation of 790-nm-pumped Tm-doped fibers," Appl. Opt. 48, 5072-5075 (2009)

S.D. Jackson, "The spectroscopic and energy transfer characteristics of the rare earth ions used fr silicate glass fibre lasers operating in the shortwave infrared," Laser & Photon. Rev., 3: 466–482. doi: 10.1002/lpor.200810058

Peter F. Moulton, Glen A. Rines, Evgueni V. Slobodtchikov, Kevin F. Wall, Gavin Frith, Bryce Samson, and Adrian L.G. Carter, "Tm-Doped Fiber Lasers: Fundamentals and Power Scaling," IEEE Journal of Selected Topics in quantum Electronics, Vol. 15, No. 1, Jan/Feb 2009

2006

 

Alexander Hemming, Shayne Bennetts, Nikita Simakov , John Haub, Adrian Carter, "Development of resonantly cladding-pumped holmium-doped fibre lasers," Proc. SPIE 8237, Fiber Lasers IX: Technology, Systems, and Applications, 82371J (February 9, 2012); doi:10.1117/12.909458

W. Torruellas, Y. Chen, B. McIntosh, J. Farroni, K. Tankala, S. Webster, D. Hagan, M. J. Soileau, M. Messerly, J. Dawson, "High peak power Ytterbium doped fiber amplifiers," Proc. SPIE 6102, Fiber Lasers III: Technology, Systems, and Applications, 61020N (February 23, 2006); doi:10.1117/12.646571

レーザによる石英ファイバの損傷

このチュートリアルではコネクタ無し(素線)ファイバ、コネクタ付きファイバ、およびレーザ光源に接続するその他のファイバ部品に関連する損傷メカニズムを詳しく説明しています。そのメカニズムには、空気/ガラス界面(自由空間結合時、またはコネクタ使用時)ならびにファイバ内における損傷が含まれます。ファイバ素線、パッチケーブル、または溶融型カプラなどのファイバ部品の場合、損傷につながる複数の可能性(例:コネクタ、ファイバ端面、機器そのもの)があります。ファイバが対処できる最大パワーは、常にそれらの損傷メカニズムの中の最小の限界値以下に制限されます。

損傷閾値はスケーリング則や一般的なルールを用いて推定することはできますが、ファイバの損傷閾値の絶対値は利用方法やユーザ定義に大きく依存します。このガイドは、損傷リスクを最小に抑える安全なパワーレベルを推定するためにご利用いただくことができます。適切な準備と取扱い方法に関するガイドラインにすべて従えば、ファイバ部品は規定された最大パワーレベルで使うことができます。最大パワーの値が規定されていない場合は、部品を安全に使用するために下表の「実用的な安全レベル」の範囲に留めてご使用ください。 パワー処理能力を低下させ、ファイバ部品に損傷を与える可能性がある要因は、ファイバ結合時のミスアライメント、ファイバ端面の汚れ、あるいはファイバそのものの欠陥などですが、これらに限られるわけではありません。特定の用途におけるファイバのパワー処理能力に関するお問い合わせは当社までご連絡ください。

Power Handling Limitations Imposed by Optical Fiber
Click to Enlarge

損傷のないファイバ端
Power Handling Limitations Imposed by Optical Fiber
Click to Enlarge

損傷のあるファイバ端

空気/ガラス界面における損傷

空気/ガラス界面ではいくつかの損傷メカニズムが存在する可能性があります。自由空間結合の時、またはコネクタで2本のファイバを結合した時、光はこの界面に入射します。高強度の光は端面を損傷し、ファイバのパワー処理能力の低下や恒久的な損傷につながる場合があります。コネクタ付きのファイバで、コネクタがエポキシ接着剤でファイバに固定されている場合、高強度の光によって発生した熱により接着剤が焼けて、ファイバ端面に残留物が残る可能性があります。

Estimated Optical Power Densities on Air / Glass Interfacea
TypeTheoretical Damage ThresholdbPractical Safe Levelc
CW
(Average Power)
~1 MW/cm2~250 kW/cm2
10 ns Pulsed
(Peak Power)
~5 GW/cm2~1 GW/cm2
  • すべての値はコネクタ無し(素線)の石英ファイバに対する仕様で、クリーンな状態のファイバ端面への自由空間結合に適用されます。
  • 損傷リスク無しでファイバ端面に入射できる最大パワー密度の推定値です。これはシステムに大きく依存するため、ハイパワーで使用する前に光学系内のファイバ部品の性能ならびに信頼性の確認をお客様ご自身で実施していただく必要があります。
  • ほとんどの使用状態でファイバを損傷することなく端面に入射できる安全なパワー密度の推定値です。

ファイバ素線端面での損傷メカニズム

ファイバ端面での損傷メカニズムはバルクの光学素子の場合と同様なモデル化ができ、UV溶融石英(UVFS)基板の標準的な損傷閾値を石英ファイバに当てはめることができます。しかしバルクの光学素子とは異なり、光ファイバの空気/ガラス界面においてこの問題に関係する表面積やビーム径は非常に小さく、特にシングルモードファイバの場合はそれが顕著です。 パワー密度が与えられたとき、ファイバに入射するパワーは、小さいビーム径に対しては小さくする必要があります。

右の表では光パワー密度に対する2つの閾値が記載されています。理論的な損傷閾値と「実用的な安全レベル」です。一般に、理論的損傷閾値は、ファイバ端面の状態も結合状態も非常に良いという条件で、損傷のリスク無しにファイバの端面に入射できる最大パワー密度の推定値を表しています。「実用的な安全レベル」のパワー密度は、ファイバ損傷のリスクが極めて小さくなる値を示しています。ファイバまたはファイバ部品をこの実用的な安全レベルを超えて使用することは可能ですが、その時は取扱い上の注意事項を適切に守り、使用前にローパワーで性能をテストする必要があります。

シングルモードの実効面積の計算
シングルモードファイバの実効面積は、モードフィールド径(MFD)、すなわちファイバ内の光が伝搬する部分の断面積によって定義されます。この面積にはファイバのコアとクラッドの一部が含まれます。シングルモードファイバとの結合効率を良くするためには、入射ビーム径をファイバのモードフィールド径に合致させなければなりません。

例として、シングルモードファイバSM400を400 nmで使用した時のモードフィールド径(MFD)は約Ø3 µmで、SMF-28 Ultraを1550 nmで使用したときのモードフィールド径(MFD)はØ10.5 µmです。これらのファイバの実効面積は下記の通り計算します。

SM400 Fiber: Area = Pi x (MFD/2)2 = Pi x (1.5 µm)2 = 7.07 µm= 7.07 x 10-8 cm2

 SMF-28 Ultra Fiber: Area = Pi x (MFD/2)2 = Pi x (5.25 µm)2 = 86.6 µm= 8.66 x 10-7 cm2

ファイバ端面が対応できるパワーを推定するには、パワー密度に実効面積を乗じます。なおこの計算は均一な強度プロファイルを想定しています。しかしほとんどのレーザービームでは、シングルモード内でガウス分布を示すため、ビームの端よりも中央のパワー密度が高くなります。よって、これらの計算は損傷閾値または実用的安全レベルに対応するパワーとは若干異なることを考慮する必要があります。連続光源を想定して上記のパワー密度の推定値を使用すると、それぞれのパワーは下記のように求められます。

SM400 Fiber: 7.07 x 10-8 cm2 x 1 MW/cm2 = 7.1 x 10-8 MW = 71 mW (理論的損傷閾値)
     7.07 x 10-8 cm2 x 250 kW/cm2 = 1.8 x 10-5 kW = 18 mW (実用的な安全レベル)

SMF-28 Ultra Fiber: 8.66 x 10-7 cm2 x 1 MW/cm2 = 8.7 x 10-7 MW = 870 mW (理論的損傷閾値)
           8.66 x 10-7 cm2 x 250 kW/cm2 = 2.1 x 10-4 kW = 210 mW (実用的な安全レベル)

マルチモードの実効面積
マルチモードファイバの実効面積は、そのコア径によって定義されますが、一般にシングルモードファイバのMFDよりもはるかに大きくなります。当社では最適な結合を得るためにコア径のおよそ70~80%にビームを集光することをお勧めしています。マルチモードファイバでは実効面積が大きくなるほどファイバ端面でのパワー密度は下がるので、より大きな光パワー(通常キロワットオーダ)を入射しても損傷は生じません。

フェルール・コネクタ付きファイバに関する損傷メカニズム

Click to Enlarge
コネクタ付きシングルモード石英ファイバに入力可能なパワー処理限界値(概算)を示したグラフ。各線はそれぞれの損傷メカニズムに応じたパワーレベルの推定値を示しています。 入力可能な最大パワーは、損傷メカニズムごとに制限されるパワーのうちの一番小さな値(実線で表示)によって制限されます。

コネクタ付きファイバのパワー処理能力に関しては、ほかにも考慮すべき点があります。ファイバは通常、エポキシ接着剤でセラミック製またはスチール製のフェルールに取り付けられています。光がコネクタを通してファイバに結合されると、コアに入射せずにファイバを伝搬する光は散乱されてファイバの外層からフェルール内へ、さらにフェルール内でファイバを保持する接着剤へと伝搬します。光の強度が大きいとエポキシ接着剤が焼け、それが蒸発して残留物がコネクタ端面に付着します。これによりファイバ端面に局所的に光を吸収する部分ができ、それに伴って結合効率が減少して散乱が増加するため、さらなる損傷の原因となります。

エポキシ接着剤に関連する損傷は、いくつかの理由により波長に依存します。一般に、光の散乱は長波長よりも短波長で大きくなります。短波長用のMFDの小さなシングルモードファイバへの結合時には、ミスアライメントに伴ってより多くの散乱光が発生する可能性があります。

エポキシ樹脂が焼損するリスクを最小に抑えるために、ファイバ端面付近のファイバとフェルール間にエポキシ接着剤の無いエアギャップを有するファイバーコネクタを構築することができます。当社の高出力用マルチモードファイバーパッチケーブルでは、このような設計のコネクタを使用しております。

複数の損傷メカニズムがあるときのパワー処理限界値を求める方法

ファイバーケーブルまたはファイバ部品において複数の損傷要因がある場合(例:ファイバーパッチケーブル)、入力可能なパワーの最大値は必ずファイバ部品構成要素ごとの損傷閾値の中の一番小さな値により決まります。この値が一般的にはパッチケーブルの端面に入射可能な最大のパワーを表します(出力パワーではありません)。 

右のグラフは、シングルモードパッチケーブルにおけるファイバ端面での損傷とコネクタでの損傷に伴うパワー処理限界の推定値を例示しています。 ある波長におけるコネクタ付きファイバの総合的なパワー処理限界値は、その波長に対する2つの制限値の小さい方の値(実線)によって制限されます。488 nm付近で使用しているシングルモードファイバは主にファイバ端面の損傷(青い実線)によって制限されますが、1550 nmで使用しているファイバはコネクタの損傷(赤い実線)によって制限されます。

マルチモードファイバの実効面積はコア径で定義され、シングルモードファイバの実効面積より大きくなります。その結果、ファイバ端面のパワー密度が小さくなり、大きな光パワー(通常キロワットオーダ)を入射してもファイバに損傷は生じません(グラフには表示されていません)。しかし、フェルール・コネクタの損傷による限界値は変わらないため、マルチモードファイバが処理できる最大パワーはフェルールとコネクタによって制限されることになります。

上記の値は、取り扱いやアライメントが適切で、それらによる損傷が生じない場合のパワーレベルです。また、ファイバはここに記載されているパワーレベルを超えて使用されることもあります。しかし、そのような使い方をする場合は一般に専門的な知識が必要で、まずローパワーでテストして損傷のリスクを最小限に抑える必要があります。その場合においても、ハイパワーで使用するファイバ部品は消耗品と捉えた方が良いでしょう。

ファイバ内の損傷閾値

空気/ガラス界面で発生する損傷に加え、ファイバのパワー処理能力はファイバ内で発生する損傷メカニズムによっても制限されます。この制限はファイバ自体が本質的に有するもので、すべてのファイバ部品に適用されます。ファイバ内の損傷は、曲げ損失による損傷とフォトダークニングによる損傷の2つに分類されます。

曲げ損失
ファイバが鋭く曲げられると、コア内を伝搬する光がコア/クラッド界面において反射する際に、その反射角が全反射臨界角よりも大きくなります。曲げ損失は、このように内部全反射ができなくなることにより生じる損失です。このような状況下では、光はファイバから局所的に漏れだします。漏れる光のパワー密度は一般に大きく、ファイバのコーティングや補強チューブが焼損する可能性があります。

特殊ファイバに分類されるダブルクラッドファイバは、コアに加えてファイバのクラッド(2層目)も導波路として機能するため、曲げ損失による損傷のリスクが抑えられます。クラッドと被覆の界面の臨界角をコアとクラッドの界面の臨界角より大きくすることで、コアから漏れた光はクラッド内に緩く閉じ込められます。その後、光はセンチメートルからメートルオーダーの距離に渡って漏れ出しますが、局所的ではないため損傷リスクは最小に留められます。当社ではメガワットレベルの大きなパワーにも対応するNA 0.22のダブルクラッドマルチモードファイバを製造、販売しております。

フォトダークニング
もう1つのファイバ内の損傷メカニズムとして、特にコアにゲルマニウムが添加されたファイバをUVや短波長の可視光で使用した時に起こるフォトダークニングまたはソラリゼーションがあります。これらの波長で使用されたファイバは時間の経過とともに減衰量が増加します。 フォトダークニングが発生するメカニズムはほとんど分かっていませんが、その現象を緩和するファイバはいくつか開発されています。例えば、水酸イオン(OH)が非常に低いファイバはフォトダークニングに耐性があることが分かっています。またフッ化物などのほかの添加物もフォトダークニングを低減させる効果があります。

しかし、上記の対応をとったとしても、UV光や短波長に使用したファイバはいずれフォトダークニングが生じます。よってこれらの波長で使用するファイバは消耗品としてお考えください。

光ファイバの準備ならびに取扱い方法

一般的なクリーニングならびに操作ガイドライン
この一般的なクリーニングならびに操作ガイドラインはすべてのファイバ製品向けにお勧めしております。さらに付属資料やマニュアルに記載された個々の製品に特化したガイドラインも遵守してください。損傷閾値の計算は、すべてのクリーニングおよび取扱い手順に適切に従ったときにのみ適用することができます。

  1. (コネクタ付き、またはファイバ素線に関わらず)ファイバを設置または組み込む前に、すべての光源はOFFにしてください。これにより、損傷の可能性のあるコネクタまたはファイバの脆弱な部分に集光されたビームが入射しないようにすることができます。

  2. ファイバやコネクタ端面の品質がファイバのパワー処理能力に直結します。ファイバを光学系に接続する前に必ずファイバ端を点検してください。端面はきれいで、入射光の散乱を招く汚れや汚染物質があってはなりません。ファイバ素線は使用前にクリーブし、クリーブの状態が良好であることを確認するためにファイバ端面の点検をしてください。

  3. ファイバを光学系に融着接続する場合、ハイパワーで使用する前にまずローパワーで融着接続の状態が良いことを確認してください。融着接続の品質が良くないと接続面での散乱が増え、ファイバ損傷の原因となる場合があります。

  4. システムのアライメントや光結合の最適化などの作業はローパワーで行ってください。これによりファイバの(コア以外の)他の部分の露光が最小に抑えられます。ハイパワーのビームがクラッド、被覆またはコネクタに集光された場合、散乱光による損傷が発生する可能性があります。

ハイパワーでファイバを使用するための要点
光ファイバやファイバ部品は一般には安全なパワー限界値内で使用する必要がありますが、アライメントや端面のクリーニングがとても良い理想的な条件下では、ファイバ部品のパワー限界値を上げることができる場合があります。入力または出力パワーを増加させる前に、システム内のファイバ部品の性能と安定性を確認し、またすべての安全ならびに操作に関する指示に従わなければなりません。下記はファイバ内またはファイバ部品内の光パワーをの増大させること加を検討していするときに役立つご提案です。

  1. ファイバースプライサを使用してファイバ部品をシステムに融着接続すると、空気/ファイバ界面での損傷の可能性を最小化できます。品質の高い融着接続が実現されるよう、すべて適切なガイドラインに則って実施する必要があります。融着接続の状態が悪いと、散乱や融着接続面での局所的な加熱などが発生し、ファイバを損傷する可能性があります。

  2. ファイバまたはファイバ部品の接続後、ローパワーでシステムのテストやアライメントを実施してください。システムパワーを必要な出力パワーまで徐々に上昇させ、その間、定期的にすべての部品が適切にアライメントされ、結合効率が入力パワーによって変動していないことを確認します。

  3. ファイバを鋭く曲げると曲げ損失が発生し、ファイバのストレスを受けた部分から光が漏れる可能性があります。ハイパワーで使用している時は、大量の光が小さな局所領域(歪みのある領域)から流出すると局所的に加熱され、ファイバが損傷する可能性があります。使用中はファイバの曲げが生じないよう配慮し、曲げ損失を最小限に抑えてください。

  4. また、用途に適したファイバを選ぶことも損傷防止に役立ちます。例えば、ラージモードエリアファイバは、標準的なシングルモードファイバをハイパワー光用として用いる場合の良い代替品となります。優れたビーム品質を有しながらMFDも大きいため、空気/ファイバ界面でのパワー密度は小さくなります。

  5. ステップインデックスシングルモード石英ファイバは、一般にUV光やピークパワーの大きなパルス光には使用しませんが、これはその用途に伴う空間パワー密度が大きいためです。


Posted Comments:
lisa tonnelier  (posted 2023-11-28 15:39:10.927)
Hello, What are the following characteristics of the ER30-4/125 fibre? effective absorption cross-section at the pump wavelength (980nm) effective emission cross-section at the signal wavelength (1550 nm) effective absorption cross-section at signal wavelength (1550nm) -Level 2 lifetime -Density of erbium ions in silica
ksosnowski  (posted 2023-11-30 10:35:35.0)
Thanks for reaching out to Thorlabs. The ER30-4/125 Level 2 lifetime is 9 ms. The density of erbium ions is about 2.5E+25 ions/m^3. I have reached out directly to share further details on these emission and absorption cross-sections as well.
theo philippe kagan  (posted 2023-11-28 15:30:42.743)
Hello, What are the following characteristics of the ER30-4/125 fibre? effective absorption cross-section at the pump wavelength (980nm) effective emission cross-section at the signal wavelength (1550 nm) effective absorption cross-section at signal wavelength (1550nm) -Level 2 lifetime -Density of erbium ions in silica
ksosnowski  (posted 2023-11-30 10:37:13.0)
Thanks for reaching out to Thorlabs. The ER30-4/125 Level 2 lifetime is 9 ms. The density of erbium ions is about 2.5E+25 ions/m^3. I have reached out directly to share further details on these emission and absorption cross-sections as well.
muhammad abdullah  (posted 2023-05-18 01:50:43.84)
Dear Sir: Can you please provide the dataset file for the emission and absorption cross section against wavelength.
Alex Pa  (posted 2023-02-08 07:21:26.243)
Hello, I want to select a proper fiber for EDFA, low ASE is critical in my application. Should I expect a difference in ASE between ER16-8 and ER80-8 if I the length I choose for each one of them provides the same amplification? Thank you
cdolbashian  (posted 2023-04-03 12:29:55.0)
Thank you for reaching out to us Alex. While there is likely a length of one fiber which would generate similar amplification as the other, we do not have detailed doping information for these fibers such that we could provide this data for you. I have reached out to you to discuss this.
Hamed Ahmad  (posted 2023-01-15 18:08:25.307)
Hello Thorlabs. Is there any information for erbium concentration, doping model (rectangular or Gaussian), doping radius, fiber NA and core radius of ER80-8/125?
jgreschler  (posted 2023-01-17 09:09:57.0)
Thank you for reaching out to Thorlabs. Additional data and specs can be requested by contacting techsupport@thorlabs.com. I have reached out to you directly to discuss these details.
Alexander Block  (posted 2022-09-13 13:41:22.207)
I think the Attenuation spec is listed falsely as 8 +- 8 dB, instead of 80+-8 in some places
ppestre  (posted 2022-09-16 02:58:52.0)
Thank you for your feedback! The spec has been corrected.
Amir Tehra  (posted 2022-07-12 15:49:26.067)
How much is the lifetime (tao) for ER110?
jgreschler  (posted 2022-08-02 02:29:25.0)
Thank you for reaching out to Thorlabs. The emission lifetime of the spontaneous emission in the erbium doped fibers is roughly 9 ms.
Jun Park  (posted 2021-09-01 09:39:57.407)
For three of below products ER30-4/125 ER110-4/125 M5-980-125 I want to gain 23dB. It will be pumped by 980 nm or 1480nm. 1. What pump power level should I need for each products...? 2. What length should I need for each products...? 3. Could you recommend proper LD model...? Thanks.
cdolbashian  (posted 2021-09-10 11:04:00.0)
Thank you for contacting us at Thorlabs! It seems like your performance requirements and are significantly application dependent. I have contacted you directly regarding your inquiries.
HA CHANGKYUN  (posted 2021-07-02 18:03:40.58)
Hello Thorlabs. Is there any information for erbium concentration in ppm unit?
YLohia  (posted 2021-07-02 09:37:51.0)
Hello, the estimated density of erbium ions in the M5-980-125 is typically 7.85 x 10^24 ions/m^3 or around 4400 ppm.
user  (posted 2021-03-03 19:53:38.413)
Hi! Will you be able to suggest pump power required (1480 nm pumping) and optimum active fiber length for ER30-4/125, for achieving a gain of 20 dB, for an i/p signal (1530-1560 nms) power level of 0 dBm? many thanks.
asundararaj  (posted 2021-03-04 01:44:11.0)
Thank you for contacting Thorlabs. I have contacted you directly about your application.
Muhammad Ghawas  (posted 2019-08-20 03:29:00.087)
Hi Thorlabs, I need the absorption and emission cross section curves for the ER80-8/125. Cooperation in this regards would be highly appreciated.
YLohia  (posted 2019-08-20 10:22:44.0)
Hello, I have reached out to you directly with this information.
Robert Baker  (posted 2019-07-15 18:19:00.95)
Hi Thorlabs, The dispersion data are nice but it would help a lot of ultrafast fiber laser people if you quoted your dispersion for every fiber in standard units. So from the graph I can easily calculate that it's 1 ps in approx 10 nm which over 5 meters gives 1 ps/ 10 nm / 0.005 km = 20 ps/nm-km This is approximately 2.6e-26 s^2/m. If you quote values in this format for your gain fibers, and especially if you quote higher order dispersion data, ultrafast fiber laser people will buy more from Thorlabs merely because they can simulate before they buy and a lot of the product data is proprietary. For instance, I'm using some Er-30 right now and I tried to simulate the dispersion to higher order but since the index data are proprietary I can't even do that. There are many ways to get to the same dispersion values so I think it makes sense for me the customer to get full dispersion curves measured or at least simulated by suppliers to higher order. This way I know what I'm buying in terms that the scientific ultrafast community is used to.
YLohia  (posted 2019-08-19 09:34:58.0)
Hello Robert, thank you for your feedback. The nominal GVD for the ER30-4/125 is 2.30E-26 s^2/m. We will look into providing this data on the website.
117011  (posted 2018-01-09 17:41:56.173)
I'm interested in dispersion of ER16-8/125. can you provide dispersion data of it?
tfrisch  (posted 2018-03-20 04:30:56.0)
Hello, thank you for contacting Thorlabs. We can email you simulated dispersion data.
till.walbaum  (posted 2017-03-30 09:25:23.063)
For the dispersion data given for Er80-8 and Er110-4, what fiber lengths were measured? Can you provide dispersion data in terms of GVD instead of GD, e.g. ps/(nm km) or ps^2/m?
tfrisch  (posted 2017-04-18 03:53:30.0)
Hello, thank you for contacting Thorlabs. The data listed on our webpage was taken with 5m of Er30-4/125 and 1m of Er80-8/125. I see that you have already contacted Tech Support for further details.
xgsun  (posted 2016-06-13 07:48:49.787)
what is the absorption ~1450 to 1480 for ER80-8/125? can you send me the absorption spectrum? Thank
besembeson  (posted 2016-06-14 03:44:17.0)
Response from Bweh at Thorlabs USA: On the product page, we do provide the peak absorption at 1530nm and the normalized absorption spectrum that can be used to estimate the absorption at your wavelengths of interest.
scottie730318  (posted 2015-05-13 23:25:15.49)
Dear Sir: we have purchased the Er-doped gain fiber (LIEKKI™ Er80-8/125). Could you provide us the splicing parameters which are used to splice the "Er80-8/125 and SMF-28" and "Er80-8/125 and Hi-1060"? Our fusion splicer is the model: FSM-60s from Fujikura. Thank you very much Best Wishes
rwalz  (posted 2015-07-30 04:16:18.0)
Hello. We do not have splicing profiles or recommendations for the various fiber fusion devices. The fiber physical specifications are available on the "Specs" tab on the product page.
taoliu  (posted 2013-12-12 08:24:26.63)
Hi, I am interrested in the absorption curve (in dB/m) and the emission curve (if possible) for Er30-4 and Er80-4 doped fibers.
pbui  (posted 2013-12-31 11:50:41.0)
Response from Phong at Thorlabs: We will contact you directly to provide the emission/absorption curves for the Er30-4/125 and Er80-4/125 fibers.
skyzeus  (posted 2013-12-02 21:33:47.323)
Hi, I am interrested in the GVD curve for Er80-4 and Er80-8 doped fibers. I am also interrested in the group delay curves of these fibers. If you can provide this information in text format, it would be the best, but I can also work with pdfs. Thanks
tcohen  (posted 2013-12-05 02:58:24.0)
Response from Tim at Thorlabs. Thanks for your feedback. We’ve emailed you with dispersion data.
maxime.hardy  (posted 2013-06-27 15:07:27.05)
Hi, I am interrested in the absorption curve (in dB/m) and the emission curve (if possible) for Er30-4 and Er80-4 doped fibers. I am also interrested in the group delay curves of these fibers. If you can provide this information in text format, it would be the best, but I can also work with pdfs. Thanks
pbui  (posted 2013-07-30 09:54:00.0)
Response from Phong at Thorlabs: Thank you for your interest. We will contact you directly regarding the curves for the Er30-4/125 and Er80-4/125 fibers.
fstrohkendl  (posted 2013-02-11 17:58:35.19)
From your catalogue"Large-Mode-Area (LMA) Double Cladding Erbium fibers are also available on request. These highly doped fibers have a core size from 20 to 30 µm with a 125 µm cladding." Please provide info on LMA Er doped fibers. Thank you.
tcohen  (posted 2013-02-21 15:06:00.0)
Response from Tim at Thorlabs: Thank you very much for your inquiry. I have sent you documentation directly for your review.
Laurie  (posted 2008-05-07 08:21:00.0)
Response from Laurie at Thorlabs to czakon: Thank you for your email. You should have received the absorption information requested from Fatih, a member of our our technical support staff. In addition, we will be posting this information on the website shortly so that it is more readily available. We apologize for teh extra step you had to go through to obtain this information.
czakon  (posted 2008-04-18 18:47:50.0)
Hello, I am interested in the absorption and emission curves of er80-4/125. I noticed they used to be in the faqs section of the site and i can no longer find this information. could you please send me the information n PDF format? Thanks! Nicole
Back to Top

Liekki®エルビウム添加ファイバ、SM・LMA

Key Features
ER30-4/125Extremely high, > 50% conversion
efficiency in the L band
ER110-4/125Extremely high doping concentration for short
device length and reduced nonlinearity
ER16-8/125Good spliceability, power conversion efficiency,
and spectral reproducibility
ER80-8/125For 980 nm pumps with emission at 1550 nm.
Large core and good spliceability.
  • 発光領域は1530~1610 nm、励起光源は980 nmと1480 nm
  • 優れた幾何学的特性による非常に低い複屈折と優れた接続特性
  • 励起用半導体レーザのSMファイバに対する接続損失: <0.1 dB
  • SMF-28e+ファイバに対する接続損失:<0.15 dB

用途

  • CおよびLバンドのDWDM、メトロ、CATV、PON
  • ASE光源
  • CWやパルスレーザ、および増幅器

Liekki高添加エルビウムファイバは1530~1610 nm の波長域(CまたはLバンド)で動作するファイバーレーザや増幅器に適しています。 これらのファイバは、通信用増幅器(EDFA)、ハイパワーPON/CATV ブースタ、さらに計測、工業、医療用途に使われる超短パルス用増幅器等の幅広い用途でお使いいただけます。 クラッド径は標準的なØ125 µmです。

Item #TypePeak Core Absorption
at 1530 nm
 Mode Field Diameter
at 1550 nm
Cladding
Diameter
Coating
Diameter
Core NA
(Nominal)
Cut-Off
Wavelength
Core
Index
Cladding
Index
ER30-4/125Single Mode30.0 ± 3.0 dB/m6.5 ± 0.5 µm125 ± 2 µm245 ± 15 µm0.2890 ± 90 nmProprietaryaProprietarya
ER110-4/125110.0 ± 10.0 dB/m
ER16-8/125Large Mode Area16.0 ± 3.0 dB/m9.5 ± 0.8 µm0.131250 ± 150 nm
ER80-8/12580.0 ± 8.0 dB/m
  • この仕様については開示されておりませんのでご了承ください。
+1 数量 資料 型番 - ユニバーサル規格 定価(税抜) 出荷予定日
ER30-4/125 Support Documentation
ER30-4/125Erbium Doped Fiber, 30 dB/m @ 1530 nm, 0.2 NA, Standard
¥3,347
Per Meter
Volume Pricing
7-10 Days
ER110-4/125 Support Documentation
ER110-4/125Erbium Doped Fiber, 110 dB/m @ 1530 nm, 0.2 NA, Standard
¥14,792
Per Meter
Volume Pricing
7-10 Days
ER16-8/125 Support Documentation
ER16-8/125Erbium Doped Fiber, 16 dB/m @ 1530 nm, 0.13 NA, Standard
¥10,760
Per Meter
Volume Pricing
7-10 Days
ER80-8/125 Support Documentation
ER80-8/125Erbium Doped Fiber, 80 dB/m @ 1530 nm, 0.13 NA, Standard
¥14,792
Per Meter
Volume Pricing
7-10 Days
Back to Top

MetroGainエルビウム添加SMファイバ

  • Lバンド出力(1565~1625 nm)で、励起光980 nmに対応
  • 短い増幅部やレーザ共振器の用途に適した高い吸収率

用途

  • Lバンド用増幅器
  • ASE光源

MetroGainエルビウム添加ファイバM12-980-125は、励起光源980 nmでのLバンド出力に適しています。 また、吸収率が高いので、標準的なLバンド出力のエルビウム添加ファイバに比べ、アクティブファイバ長が短くできます。

これらのファイバは、添加領域と励起光のモードがよく一致しており、かつ優れた接続特性も有します。MetroGainファイバは高い吸収率を有するので、ファイバーレーザやASE光源に適します。 ファイバーレーザの共振器の長さが非常に短くて済むので、パルスの歪みは最小限に抑えられます。

Item #TypeEmission
Wavelength
AbsorptionMFD @ 1550 nm
(Nominal)
Cladding
Diameter
Coating Diameter
(Nominal)
Core NACut-Off
Wavelength
Core/Cladding
Index
M12-980-125Single ModeL-Band11.0 - 13.0 dB/m @ 980 nm
16.0 - 20.0 dB/m @ 1531 nm
5.7 - 6.6 µm125 ± 1 µm245 ± 15 µm 0.21 - 0.24900 - 970 nmProprietarya
  • この仕様については開示されておりませんのでご了承ください。
+1 数量 資料 型番 - ユニバーサル規格 定価(税抜) 出荷予定日
M12-980-125 Support Documentation
M12-980-125Erbium Doped L Band Fiber
¥2,229
Per Meter
Volume Pricing
7-10 Days
Last Edited: Jan 09, 2014 Author: Dave Gardner