顕微鏡用LED照明、コリメーター付き


  • UV, Visible, and IR LEDs
  • Mounted LED with Adjustable Collimation Optic
  • Compatible with Epi-Illumination Port on Olympus, Leica, Nikon,
    and Zeiss Microscopes

M625L4-C1

For Olympus
BX/IX Microscopes

M590L4-C5

For Nikon Eclipse
Microscopes

M405LP1-C2

For Leica DMI
Microscopes

M850L3-C4

For Zeiss Axioskop
Microscopes

M505L4-C1 Used
as a Light Source for
an Olympus IX71

Related Items


Please Wait

特長

  • 顕微鏡の落射照明用ポート、プロジェクタ、ならびにカスタム仕様のイメージングシステム用照明
  • 適切な温度管理による安定した出力強度
  • 調整可能で低F値(約0.8)のコリメート用非球面レンズ
  • 内蔵のEEPROMがLED動作パラメータを記憶
  • 高出力LEDはØ57.0 mmのプラスチック製筐体にマウント済み(詳細は右表参照)
  • カスタム仕様の電源用に4ピンメスコネクタもご用意(別売り)
  • カスタム仕様のアダプタもご提供可能(詳細については当社までお問い合わせください)

当社のコリメータ付きLED照明は、OlympusLeicaNikonZeissなど市販されているほとんどの顕微鏡の標準的な落射照射用ポートに取り付けることができます。 各コリメータ付きLED照明は、マウント済み高出力LEDと、ARコーティング付き非球面コリメートレンズ内蔵で、ランプハウスポートに取り付け可能な筐体で構成されています(詳細は、「仕様」タブをご覧ください)。当社のマウント付きLED高出力LED Solis®のラインナップは、こちらのページにはない波長や光出力のご用意もございます。

注: 事前にお手持ちの顕微鏡が外部照明を直接接続できる構成であることをご確認ください。顕微鏡によっては、照明を取り外すことができず下記のLED照明をお使いいただけない場合がございます。

ビームのコリメートは、LEDに対する非球面レンズの位置を変更することで調整することができます。 LEDの交換は簡単です。筐体に取付けられているLEDのネジをゆるめ、新しいマウント付きLED(別売り)と交換してください。また、当社ではこちらのLED製品とは別にお買い求めになれるコリメートアダプタもご用意しております。

コリメート用アダプタを通ったビームの合計出力値は下表ならびに「仕様」のタブでご覧いただけます。 なお試料面における実際の出力値は、顕微鏡の光学セットアップ特有の損失によって低くなります。 お客様がセットアップされた顕微鏡の試料面での出力値を測定いただけるよう、顕微鏡用スライドパワーメータをご用意しております。

このコリメートLEDのパッケージは、当社のマウント済み高出力LEDと同様、ヒートシンクに直接接しているため、優れた温度管理機能を有します。 これにより、LEDの温度の上昇による光出力の低下を最小限に抑えることができます。 コリメートLEDの安定した出力強度については「安定性」タブをご覧ください。また、M365LP1、M385LP1、M405LP1は出力が高く、放熱と熱安定性を高めるために大型(Ø57.0 mm)のプラスチック製ヒートシンクに取り付けられています。

お使いの用途において、顕微鏡への対応よりもSM1ネジへの対応が望ましい場合、当社のマウント付きLED(別売り)はØ25.4 mm(Ø1インチ)のレンズおよびレンズチューブを用いてコリメートすることが可能です。このコリメート法では、このページでご紹介しているコリメータをお使いいただく場合よりも小さなビーム径が得られます。製品リストの詳細や説明は、マウント済みLEDのページのコリメート」タブをご覧ください。

ドライバ
当社では、こちらのLEDに対応するドライバとしてLEDD1BUPLEDDC2200DC4100DC4104の5種類をご用意しています(DC4100とDC4104にはDC4100-HUBが必要です)。ドライバUPLED、DC2200、DC4100、DC4104は接続されたLEDのEEPROMから電流のリミット値を読み取り、最大電流値を自動的に設定してLEDを保護することができます。それぞれのドライバの仕様や比較については「LEDドライバ」タブをご覧ください。

LEDの仕様a

Legend
LED Mounted to a Heat Sink in a Ø57.0 mm Red HousingLED Mounted to a Heat Sink in a Ø30.5 mm Black Housing

筐体のコリメート用光学素子を保持する部分のサイズは、型番の末尾が同じであればヒートシンクのサイズに関わらず、すべてのLEDで同じです

Item # PrefixNominal
Wavelengthb,c
ColorbMin LED
Powerb,d
Typ. LED Powerb,dMax Drive
Current (CW)
Forward
Voltage (Typ.)
Irradiance
(Typical)d
Electrical
Power
Typical
Lifetime
Emitter
Size
M365L3e365 nmUV880 mW1290 mW1000 mA3.85 V14.4 µW/mm23.850 W>10 000 h2.5 mm x 2.5 mm
M365LP1e,f365 nmUV1350 mW2000 mW1700 mA4.0 V21.0 µW/mm26.800 W>10 000 h2.5 mm x 2.5 mm
M385L2e385 nmUV270 mW430 mW700 mA4.3 V11.8 µW/mm23.010 W>10 000 h1 mm x 1 mm
M385L3e385 nmUV1240 mW1780 mW1000 mA3.7 V19.9 µW/mm23.700 W>10 000 h2.5 mm x 2.5 mm
M385LP1e,f385 nmUV1650 mW1830 mW1700 mA3.9 V23.3 µW/mm26.630 W>10 000 h1.4 mm x 1.4 mm
M405L4e405 nmUV1000 mW1300 mW1000 mA3.4 V14.53 µW/mm23.400 W> 1 000 h1.4 mm x 1.4 mm
M405LP1e,f405 nmUV1500 mW1700 mW1400 mA3.45 V24.6 µW/mm24.830 W>10 000 h1.4 mm x 1.4 mm
M455L4455 nmRoyal Blue1150 mW1445 mW1000 mA3.25 V32 µW/mm21.900 W>100 000 h1 mm x 1 mm
M470L5470 nmg,hBlue809 mWg,h1161.7 mWg,h1000 mAg3.8 V21.4g,h,i µW/mm23.820 Wg,h>100 000 hg1 mm x 1 mm
M505L4505 nmCyan400 mW520 mW1000 mA3.5 V5.94 µW/mm23.500 mW>100 000 h1 mm x 1 mm
M530L4530 nmGreen370 mW480 mW1000 mA3.6 V9.46 µW/mm23.600 W>100 000 h1 mm x 1 mm
M590L4590 nmAmber230 mW300 mW1000 mA2.5 V6.0 µW/mm22.500 W>100 000 h1 mm x 1 mm
M617L5617 nmOrange737.4 mWg,h1006.2 mWg,h1000 mAg2.9 Vg,h19.4 µW/mm2 g,h,i2.915 Wg>100 000 hg1 mm x 1 mm
M625L4625 nmRed700 mW920 mW1000 mA2.5 V21.9 µW/mm22.500 W100 000 h1 mm x 1 mm
M660L4660 nmDeep Red940 mW1050 mW1200 mA2.6 V20.88 µW/mm23.120 W>10 000 h1.5 mm x 1.5 mm
M780L3780 nmIR200 mW300 mW800 mA2.0 V47.3 µW/mm21.600 W>10 000 h1 mm x 1 mm
M810L3810 nmIR325 mW375 mW500 mA3.6 V61.8 µW/mm21.800 W>10 000 h1 mm x 1 mm
M850L3850 nmIR900 mW1100 mW1200 mA2.95 V22.9 µW/mm23.540 W100 000 h1 mm x 1 mm
M940L3940 nmIR800 mW1000 mW1000 mA2.75 V19.1 µW/mm22.750 W100 000 h1 mm x 1 mm
MCWHL8N/AjCold White1300.9 mWg,h1882.0 mWg,h1400 mAg3.6 Vg,h22.5 µW/mm2 g,h,i5040 mWg>100 000 hgØ3 mm
  • この表にはコリメート用アダプタ無しのLEDの仕様を掲載しています。 コリメート用アダプタを取り付けたLEDの仕様についてはこのページの2つ目の表をご参照ください。
  • 製造ロットの違いや、温度、電流などの動作パラメータによって、LEDの実際の出力スペクトルは変動します。 出力値や仕様の中心波長は参考データとしてご利用ください。
  • 可視光LEDの公称波長は人間の目が最も明るく感じるLEDの波長です。 UVならびに赤外線LEDの公称波長はピーク波長に相当します。 可視光LEDの公称波長は、分光器で測定したピーク波長と一致しない場合があります。
  • LED単体の仕様。 コリメーターパッケージ付きの合計出力値は下の表をご覧ください。
  • 当社の365 nm~405 nmのLEDは、駆動中に強いUV光を放射します。UV光を直接見ないよう十分にご注意ください。また、目の損傷を防ぐためUV光用保護メガネを必ず着用してください。 皮膚など体の一部をUV光に曝さないようご注意ください。
  • これらのLEDは、出力パワーが高く(合計出力値については下表および「仕様」タブ参照)、放熱を高めるため大型(Ø57.0 mm)のプラスチック製ヒートシンクに取り付けられています。
  • 25 °Cで測定
  • 最大電流での駆動時
  • 200 mmの位置において測定
  • 相関色温度6500K

コリメート用顕微鏡アダプタを取り付けたLEDの仕様

Legend
LED Mounted to a Heat Sink in a Ø57.0 mm Red HousingLED Mounted to a Heat Sink in a Ø30.5 mm Black Housing

筐体のコリメート用光学素子を保持する部分のサイズは、型番の末尾が同じであればヒートシンクのサイズに関わらず、すべてのLEDで同じです

Item # Suffix-C1-C2-C4-C5
Compatible MicroscopeaOlympus BX and IXLeica DMIZeiss Axioskop and ExaminerbNikon Eclipse (Bayonet Mount)
Beam Diameterc,d50 mm37 mm44 mm43 mm
Beam Areac1960 mm²1080 mm²1520 mm²1450 mm²
Item # PrefixIncluded Collimation LensTotal Beam Powerc,d
M365L3ACL5040U-A520 mW320 mW430 mW320 mW
M365LP1ACL5040U-A745 mW435 mW615 mW435 mW
M385L2ACL5040U-A170 mW90 mW110 mW120 mW
M385L3ACL5040U-A680 mW450 mW570 mW410 mW
M385LP1ACL5040U-A795 mW520 mW660 mW630 mW
M405L4ACL5040U-A510 mW310 mW410 mW380 mW
M405LP1ACL5040U-A750 mW450 mW580 mW570 mW
M455L4ACL5040U-A630 mW490 mW690 mW630 mW
M470L5ACL5040U-A487 mW402 mW521 mW487 mW
M505L4ACL5040U-A220 mW170 mW240 mW220 mW
M530L4ACL5040U-A200 mW160 mW220 mW200 mW
M590L4ACL5040U-A130 mW100 mW140 mW130 mW
M617L5ACL5040U-A484 mWe362 mWe474 mWe441 mWe
M625L4ACL5040U-A630 mW490 mW690 mW630 mW
M660L4ACL5040U-A590 mW400 mW570 mW520 mW
M780L3ACL5040U-B210 mW130 mW180 mW170 mW
M810L3ACL5040U-BN/A210 mWN/AN/A
M850L3ACL5040U-B480 mW330 mW400 mW370 mW
M940L3ACL5040U-B430 mW320 mW380 mW340 mW
MCWHL8ACL5040U-A658 mWf419 mWf596 mWf549 mWf
  • 標準、もしくは落射照明用ポートが必要です。
  • こちらのアダプタはZeiss製Axioskop顕微鏡およびExaminer顕微鏡と同じアリ溝を使用している全てのZeiss製顕微鏡にご使用いただけます。
  • LEDの実際の合計出力値、ビーム径、ビーム面積は、製造ロットの違いや、温度や電流などの動作パラメータによって変動します。
  • コリメーターパッケージの出力開口における値
  • 最大電流での駆動時
  • 25℃で測定

LEDの実際の出力スペクトルや合計出力値は、製造ロットの違いや、温度や電流などの動作パラメータによって変動します。 適切なLEDをお選びいただくために各コリメートLEDの典型的な合計出力値を明記しました。 LEDの出力値を異なる公称波長において比較するため、下記プロット図のスペクトルは各コリメートLEDの典型的な合計出力値を基準に記載されています。これらのデータは代表例です。各コリメーターパッケージの規格化ならびに基準化されたスペクトルのエクセルファイルのデータは、各グラフ下のリンクをクリックしてダウンロードすることができます。

Olympus製BXおよびIX顕微鏡用コリメートLED光源

Olympus BX and IX Collimated LED
Click to Enlarge

上のグラフのデータのエクセルファイルはこちらからダウンロードいただけます。

Leica製DMI顕微鏡用コリメートLED光源

Leica DMI Collimated LED
Click to Enlarge

上のグラフのデータのエクセルファイルはこちらからダウンロードいただけます。

Nikon製Eclipse顕微鏡用コリメートLED光源

Nikon Eclipse Collimated LED
Click to Enlarge

上のグラフのデータのエクセルファイルはこちらからダウンロードいただけます。

Zeiss製Axioskop顕微鏡用コリメートLED光源

Zeiss Axioskop Collimated LED
Click to Enlarge

上のグラフのデータのエクセルファイルはこちらからダウンロードいただけます。

LEDの寿命および長期的なパワー安定性

LEDの特性の1つとして、時間の経過と共にパワーが自然に低下することがあげられます。ほとんどの場合、パワーは緩やかに低下しますが、急速な低下や完全な停止、あるいは故障が突然起こることもあります。 LEDの寿命は、LEDの種類ごとに規定されたある割合のLEDが、あるパワーレベル以下に低下するまでの時間で定義されます。寿命測定のパラメータはBXX/LYYで表され、ここでXXはその種類のLEDで寿命が過ぎた後の出力パワーが規定値のYY%以下になるLEDの割合を示します。当社では、LEDの寿命をB50/L50で表しますが、これはその型番のLEDのうち50%のLEDの光パワーが規定の寿命がきた時に初期値の50%以下に低下するという意味です。例えば、定格出力パワー150 mWのLED100個のうち、50個の出力パワーが規定の寿命を過ぎたときに75 mW以下に低下するということです。

最適化された温度管理

このコリメート済みLEDの放熱特性は最適化されています。LEDパッケージのヒートシンクはLEDマウントのヒートシンクと直接熱的接触をしているので、放熱は適切な状態になっています。これにより、LED接合部の温度上昇に起因する光出力パワーの低下が最小限に抑えられます(右のグラフをご参照ください)。

PinSpecificationColor
1LED AnodeBrown
2LED CathodeWhite
3EEPROM GNDBlack
4EEPROM IOBlue

Pin Out

ピン接続:オス型

右の図は、コリメートしたLEDアセンブリのオス型コネクタを示しています。 これは、標準的なM8x1センサ円形コネクタです。 ピン1と2はLED接続用です。 ピン3と4はLEDに内蔵するEEPROMに使用されます。 当社以外のLEDドライバをご使用の場合、ピン1と2の接続は適切に行ってください。またEEPROMピンからLED駆動しないようご注意ください。

駆動するLEDからその最大光パワーを出力させるには、ドライバの最大電圧と最大電流が、それぞれLEDの最大電圧以上、最大電流以上であることが必要です。

Compatible DriversLEDD1BUPLEDaDC2200aDC4100a,bDC4104a,b
Click Photos to EnlargeLEDD1B DriverupLED DriverDC2200 DriverDC4100 DriverDC4104 Driver
LED Driver Current Output (Max)c1.2 A1.2 ALED1 Terminal: 10.0 A
LED2 Terminal: 2.0 Ad
1.0 A per Channel1.0 A per Channel
LED Driver Forward Voltage (Max)12 V8 V50 V5 V5 V
Modulation Frequency Using External Input (Max)5 kHz-250 kHze,f100 kHzf
(Simultaneous Across all Channels)
100 kHzf
(Independently Controlled Channels)
External Control Interface(s)Analog (BNC)USB 2.0USB 2.0 and Analog (BNC)USB 2.0 and Analog (BNC)USB 2.0 and Analog (8-Pin)
Main Driver FeaturesVery Compact Footprint
60 mm x 73 mm x 104 mm
(W x H x D)
USB-ControlledTouchscreen Interface with Internal and External Options for Pulsed and Modulated LED Operation4 Channelsb4 Channelsb
EEPROM Compatible: Reads Out LED Data for LED Settings-YesYesYesYes
LCD Display--YesYesYes
  • 電流はEEPROMからの読み出し情報により最大値を自動的に制限します。
  • ドライバDC4100ならびにDC4104をDC4100-HUBと使用すれば、最大4個のLEDの電力供給と制御が同時に行うことができます。 こちらのページに掲載されているLEDにドライバDC4100またはDC4104をご使用になる場合には、DC4100-HUBが必要です。
  • LEDの最大定格電流がドライバの最大出力電流を超えていても駆動することは可能ですが、その場合は最大出力には到達できません。各LEDの最大定格電流については「仕様」タブをご覧ください。
  • 下記に掲載されているコリメートLEDは、LED2端子に接続可能です。
  • 小信号帯域幅:フルスケール電流の20%を超えない正弦波変調。このドライバはほかの波形にも対応しますが、その際最大周波数も下がります。
  • MCWHL8-Cの白色光は蛍光の光刺激によって生成されているので、5 kHzを超えた周波数に変調時、LED光が完全に消灯しない場合があります。

Posted Comments:
Yeon Jae Yoo  (posted 2022-11-01 08:57:41.63)
Hello. My name is YeonJae Yoo, who works for LG Chem in Korea. I am writing this email because I have an inquiry regarding the purchase of a 365nm wavelength LED. If I buy this product, will the 365nm LED collimated beam come out without any other accessories? I want to know if I need to purchase another driver. Please reply by e-mail.
hchow  (posted 2022-11-02 05:38:44.0)
Hi Ms. Yoo, thank you for your enquiry. I will personally reach out to you to provide more information.
user  (posted 2021-03-23 20:31:18.53)
Dear sir, I am looking for collimated LED light sources which are internally or externally SM2 threaded (like Solice LEDs). This would be very universal and convenient for integrating them with other thorlabs optics. They can be surely compatible with microscopes using, for example, SM2A13. I have a Solice LED for this purpose but need lighter one such as MCWHL6-C1. Alternatively, it would be great for you to provide adapters to fit MCWHL6-C1 to SM2 threaded parts. Thanks.
MKiess  (posted 2021-03-25 11:13:07.0)
Thank you very much for this feedback. You can use a MCWHL6 LED in combination with a SM2F32-A, adjustable collimation adapter for Ø2" (Ø50 mm) Optics for this purpose. The MCWHL6 is the same LED that is also used for the MCWHL6-C1. You can screw the SM2F32-A collimator directly to this LED. The collimator has an internal SM2 thread for further integration.
Patrick Lee  (posted 2021-03-09 11:23:47.873)
Hi, I am interested in MCWHL6-C1. I plan to use it as a collimated light source to shine on a test object, in order to cast a shadow on a diffuser glass. A camera is placed at back of diffuser to pick up the shadow. a) what is divergence output ? b) will shadow be sharp ? c) any recommendation for power supplier ? Thank you.
MKiess  (posted 2021-03-11 08:59:36.0)
Dear Patrick, Thank you for your inquiry. A suitable LED driver for the MCWHL6-C1, is the LEDD1B or the DC2200. The divergence and sharpness of the shadow depends on your overall optical system of diffuser and lenses used, as well as the camera parameters. I have contacted you directly to discuss the details.
user  (posted 2021-02-13 00:38:28.523)
Hi, I am interested in using the MCWHL6-C5 to replace a 12V100W halogen lamphouse on my Nikon microscope. Roughly speaking, would the total output (477 mW) be comparable to the total output of the halogen bulb?
MKiess  (posted 2021-02-15 11:03:51.0)
Thank you very much for your inquiry. It depends on what the exact output power of the halogen lamp is. I assume that it will be a little higher than that of this LED. Cold white, LEDs with higher output power, which can also be connected to the Nikon microscope with corresponding collimators or adapters (As can be found, for example, under the following link.: https://www.thorlabs.de/newgrouppage9.cfm?objectgroup_id=8706) would be the SOLIS-1C and the MCWHLP1. I have contacted you directly to discuss the exact requirement together.
Hajun Song  (posted 2020-11-09 01:50:49.14)
I want to use this model as a flash lamp for the high speed camera. What is the eletrical bandwidth of the laser? Is it possble to modulate the LD as a short pulse modulation? How narrow?
wskopalik  (posted 2020-11-09 10:39:33.0)
Dear Hajun, Thank you very much for your feedback. Unfortunately we do not have any data about the rise time of the M780L3-C1. Usually the bandwidth of LEDs is limited by the driver electronics rather than by the LED itself. So the specifications of the driver would need to be considered in most cases. A good assumption for the rise time of an LED without phosphor like the M780L3-C1 is the range of at least 100 ns. This corresponds to an 3dB bandwidth of 3.5 MHz. Phosphor-converted LEDs (e.g. for white light) can however be considerably slower than that. I will contact you directly so we can talk about your requirements in more detail.
yefan8900  (posted 2019-02-07 15:20:32.607)
can you please recommend me a led driver of this led? 1600 mA
swick  (posted 2019-02-15 05:12:49.0)
This is a response from Sebastian at Thorlabs. Thank you for the inquiry. Our DC2200 can be used to drive LEDs at 1600 mA.
yefan8900  (posted 2019-02-07 14:11:44.557)
what's the beam power of M470L2-C3 - Blue (470 nm)? the spec sheet does not have such information. only have information about M470L2-C1, M470L2-C2, M470L2-C4, M470L2-C5.
nreusch  (posted 2019-04-15 10:48:41.0)
This is a response from Nicola at Thorlabs. Thank you for your inquiry! The total beam power is 300 mW. I will send you the spec sheet via email.
yefan8900  (posted 2019-02-06 22:17:30.557)
Can you send me the spec sheet of M470L2-C3? The spec sheet above did not include M470L2-C3, which is very weird.
nreusch  (posted 2019-04-15 10:48:38.0)
Thank you for your inquiry! Please find my response below your second post.
e.zherebtsov  (posted 2017-08-04 02:35:01.72)
Could you consult me please whether it is possible to modulate the LEDs at 365 nm with frequency ~50 MHz. Thanks a lot.
tschalk  (posted 2017-08-07 09:13:59.0)
This is a response from Thomas at Thorlabs. These high power LEDs are not well suited to perform a modulation in the MHz range. We will contact you directly with more detailed information.
iravkin  (posted 2017-08-02 09:50:36.14)
Could you explain the procedure and the light meters used to measure the Total Beam Power at the output aperture of collimated LED light sources? Do you offer the required power meters if I want to perform these measurements in my lab?
tfrisch  (posted 2017-08-16 10:36:19.0)
Hello, thank you for contacting Thorlabs. These collimated LEDs are measured using an integrating sphere which is unfortunately not a component we offer. We will reach out to you directly as well.
tzangle  (posted 2017-01-18 22:29:19.993)
What is the "separate adapter that is available from Olympus." that may be necessary to use this with an IX series microscope as a transmitted light source?
wskopalik  (posted 2017-01-24 06:24:23.0)
This is a response from Wolfgang at Thorlabs. Thank you very much for your inquiry. The collimated LED light sources for Olympus BX and IX microscopes can be directly attached to the epi-illumination port of these microscopes. For the transmission-illumination port we might be able to offer a suitable collimator as a special. I have contacted you directly to provide further information and to discuss the issue in more detail.
bmsalzbe  (posted 2016-02-29 11:41:02.43)
Need amplitude noise information at 530 nm and 470 nm
shallwig  (posted 2016-03-03 09:53:52.0)
This is a response from Stefan at Thorlabs. Thank you very much for your inquiry. I will contact you directly to check your setup and your application in detail.
giulia.mazza  (posted 2014-03-20 10:48:54.817)
Hello! The LED M455L3 would suite my application, I'm looking for possibilities to collimate it correctly ideally in a small beam with low divergence.. I do not need it for microscopy. A 5 cm diameter beam is quite big but if the collimation is good I could resize it with further optics, so the first question is "which is the divergence of the beam after collimation in the product M455L3-C1"? Second question, are there other possibilities to collimate the M455L3 LED in for example a < 1.5 cm beam with divergence < 5°? How much power loss should it cause?? Thanks in advance!!!
jvigroux  (posted 2014-04-10 10:10:14.0)
A response from Julien at Thorlabs: Thank you for your inquiry! The divergence of the M455L3-C1is typically of about 3° and in best case slightly less than 2°, so that in principle it would be possible to resize the beam after the 2" output. By using another collimating lens than the standard 2" diameter 40mm focal length, one can further reduce the output collimated beam. I will contact you directly to discuss the requirements in termsof powe and divergence in order to see which option would work best in your case.
mwinkler.its-b2011  (posted 2013-09-26 07:33:22.427)
Hello, I have bought the MCWHL5-C1 and I would like to mount it externally on a bar to a device. Sadly I am not sure which mount I should best use where I can put the device in and connect it to the bar with screws. Can you recommend me a device from your catalogue which is best suited for that? Thanks in advance
tschalk  (posted 2013-10-04 08:15:00.0)
This is a response from Thomas at Thorlabs. Thank you very much for your inquiry. To mount our collimated LED light sources you can use a lens tube slip ring SM1RC: https://www.thorlabs.de/newgrouppage9.cfm?objectgroup_id=1533&pn=SM1RC#2714. I will contact you directly with more detailed information.
mhunter  (posted 2013-09-11 14:07:09.973)
I am very interested in using an LED light source in place of a 100 watt halogen lamp -- in the EPI illuminators of my (6) Nikon Optiphot 150 microscopes. We are primarily using brightfield and DIC imaging. Would your mounted LEDs (probably cool white or green) work in this application? Thanks, Mike Hunter
tschalk  (posted 2013-09-13 09:50:00.0)
A response from Thomas at Thorlabs. Thank you very much for your inquiry. At the moment we don’t have an adapter which is suitable for the Nikon Optiphot 150 microscopes. I will contact you directly to check if we can find a solution.
B.Povazay  (posted 2013-03-12 19:54:38.977)
Is it possible to mount collimated LEDs in a standard SM1-mount?
tcohen  (posted 2013-03-14 13:37:00.0)
Response from Tim at Thorlabs: The back end of these have 1.2” diameters and can be used with an SM1RC slip ring. The beam diameters produced by these larger focal length lenses would overfill an SM1 thread. If you are looking to confine it to this size an alternative would be to use the mounted LED without the collimating optic, (this is the M***L2 series and can be purchased separately) and then use a 1” diameter lens with an adjustable length lens tube for alignment. We have a typical setup to this end on our “Application” tab on the M***L2 series page.
jvigroux  (posted 2012-10-22 08:48:00.0)
A response form Julien at Thorlabs: Thank you for your inquiry! As far as I know, DIC usually uses polarized light sources. If this is the cas ein your setup, the LEd would not work because of the light being unpolarized. The use of an extra polarizer after the LED would imply a strong power reduction as well as a relatively high instability of the output power. I will contact you directly to discuss the details of your setup in order to see which light source could be used.
nrbabuwp  (posted 2012-10-18 18:45:29.41)
Hi, We are interested in buying an LED to replace the lamp of DIC to use it in multicolor imaging. Wavelength range we are looking for is between 670 and 750nm. Can you suggest if 260mW of 735nm LED is good enough for DIC imaging? Has anyone used it for DIC? Babu
jvigroux  (posted 2012-01-23 10:30:00.0)
A response from Julien at Thorlabs: Thank you for your feedback! the suggested adapters are by no mean the only solution and based on the details of your setup, some other configuration might indeed improve the power density or the homogeneity. I will contact you directly to discuss the details and see which solution would be the most adapted.
g.raffy  (posted 2012-01-23 09:12:12.0)
A collimated beam with 50mm diameter will be clipped by the back aperture of the objective in an IX microscope (~10mm), loosing most of the available power of the LED. Am I wrong? Why not proposing an alternative lens that lets all the light entering the objective? I really need all the power... Ideally, if the lens to LED distance is settable, then one could choose between power density and uniformity of illumination.
bdada  (posted 2011-09-21 14:55:00.0)
Response from Buki at Thorlabs: Thank you for your interest in our MCWHL2-C1 and for taking the time to use our feedback tool! These mounts are designed to fit on the standard and epi-illumination ports for Olympus BX and IX microscopes. The exact compatibility will depend on whether the transmitted lamp housing on your desired Olympus microscope has the same port-style as the BX and IX. Please contact TechSupport@thorlabs.com if you have further inquiries.
mzlin  (posted 2011-09-02 12:01:15.0)
Can anyone verify that the Olympus mounts will fit in place of the transmitted lamp housing too (i.e. the same mount will work for transmitted as for fluorescence)? We have not gotten our scope yet so cant measure ourselves. Thanks.
klee  (posted 2009-10-05 16:12:24.0)
A response from Ken at Thorlabs: Our new DC2100 is also plug and play compatible with these LED light sources.
acable  (posted 2009-10-03 15:47:55.0)
Is the LEDD1 driver the only driver you offer that is plug and play compatible.

こちらのページでは当社が販売するすべてのLEDをご覧いただけます。More [+]をクリックすると、下の各LED製品の波長をご覧いただけます。

Light Emitting Diode (LED) Selection Guide
Click Photo to Enlarge
(Representative; Not to Scale)
TypeUnmounted LEDsPigtailed LEDsLEDs in
SMT Packages
LED ArraysLED Ring LightCage-Compatible
Diffuse Backlight LED
Light Emitting Diode (LED) Selection Guide
Click Photo to Enlarge
(Representative; Not to Scale)
TypePCB-
Mounted LEDs
Heatsink-
Mounted LEDs
Collimated LEDs for MicroscopybFiber-
Coupled LEDs
c
High-Power LEDs for MicroscopyMulti-Wavelength
LED Source Optionsd
  • 25℃で測定
  • これらのコリメートLEDは、以下の顕微鏡の標準ポートならびに落射照明用ポートに取り付けることができます:Olympus BX/IX(型番末尾:-C1)、Leica DMI(型番末尾:-C2)、Zeiss Axioskop(型番末尾:-C4)、Nikon Eclipse(バヨネットマウント、型番末尾:-C5)
  • コア径Ø400 µm、NA 0.39のマルチモードファイバを使用した際の典型出力
  • 当社の多波長LED光源は、対応可能な波長のLEDを組み合わせて使用できます。
  • Leica DMI用コリメーターパッケージ(型番末尾:-C2)に使用したLEDの典型値
  • これらのLEDの最大電流時におけるコリメート出力の最小出力。コリメート用レンズは各LEDに取付け済み
  • Olympus BX/IX用コリメーターパッケージ(型番末尾: -C1)に使用したLEDの典型値
  • Zeiss Axioskop用コリメーターパッケージ(型番末尾:-C4)に使用したLEDの典型値
  • 400 nm~525 nmのスペクトルの青い領域で放射されるLEDの強度(%)
Back to Top

Olympus製BXおよびIX顕微鏡用LED照明、コリメータ付き

  • ビーム径:約 50 mm
  • ビーム面積:約 1960 mm²
  • ARコーティング付き非球面コリメートレンズ(EFL = 40 mm)
  • 仕様の詳細については「仕様」タブ参照
  • ケーブルの長さ: 2 m
Item #ColoraHousingTotal Beam Powerb
M365L3-C1UV520 mW
M365LP1-C1cUV745 mW
M385L2-C1UV170 mW
M385L3-C1UV680 mW
M385LP1-C1cUV795 mW
M405L4-C1UV510 mW
M405LP1-C1cUV750 mW
M455L4-C1Royal Blue630 mW
M470L5-C1Blue487 mW
M505L4-C1Cyan220 mW
Item #ColoraHousingTotal Beam Powerb
M530L4-C1Green200 mW
M590L4-C1Amber130 mW
M617L5-C1Orange484 mWd
M625L4-C1Red630 mW
M660L4-C1Deep Red590 mW
M780L3-C1IR210 mW
M850L3-C1IR480 mW
M940L3-C1IR430 mW
MCWHL8-C1Cold White658 mWe
  • 製造ロットの違いや、温度、電流などの動作パラメータによって、LEDの実際の出力スペクトルは変動します。 出力値や仕様の中心波長は参考データとしてご利用ください。
  • コリメーターパッケージの後。製造工程および温度や電流等の駆動パラメータのバラツキによって、いずれのLEDにおいても合計出力値は変わります。
  • このLEDは出力が高いため、熱放散が向上するようにØ57.0 mmのヒートシンクに取り付けられています。
  • 最大電流での駆動時
  • 25℃で測定
+1 数量 資料 型番 - ユニバーサル規格 定価(税抜) 出荷予定日
M365L3-C1 Support Documentation
M365L3-C1365 nm, 520 mW (Typ.) Collimated LED for Olympus BX & IX, 1000 mA
¥83,871
7-10 Days
M365LP1-C1 Support Documentation
M365LP1-C1365 nm, 745 mW (Typ.) Collimated LED for Olympus BX & IX, 1700 mA
¥98,310
7-10 Days
M385L2-C1 Support Documentation
M385L2-C1385 nm, 170 mW (Typ.) Collimated LED for Olympus BX & IX, 700 mA
¥67,678
7-10 Days
M385L3-C1 Support Documentation
M385L3-C1385 nm, 680 mW (Typ.) Collimated LED for Olympus BX & IX, 1000 mA
¥86,907
7-10 Days
M385LP1-C1 Support Documentation
M385LP1-C1385 nm, 795 mW (Typ.) Collimated LED for Olympus BX & IX, 1700 mA
¥88,535
7-10 Days
M405L4-C1 Support Documentation
M405L4-C1405 nm, 510 mW (Typ.) Collimated LED for Olympus BX & IX, 1000 mA
¥74,538
7-10 Days
M405LP1-C1 Support Documentation
M405LP1-C1405 nm, 750 mW (Typ.) Collimated LED for Olympus BX & IX, 1400 mA
¥88,535
7-10 Days
M455L4-C1 Support Documentation
M455L4-C1455 nm, 630 mW (Typ.) Collimated LED for Olympus BX & IX, 1000 mA
¥86,907
7-10 Days
M470L5-C1 Support Documentation
M470L5-C1470 nm, 487 mW (Typ.) Collimated LED for Olympus BX & IX, 1000 mA
¥76,388
Today
M505L4-C1 Support Documentation
M505L4-C1505 nm, 220 mW (Typ.) Collimated LED for Olympus BX & IX, 1000 mA
¥86,907
7-10 Days
M530L4-C1 Support Documentation
M530L4-C1530 nm, 200 mW (Typ.) Collimated LED for Olympus BX & IX, 1000 mA
¥86,907
Today
M590L4-C1 Support Documentation
M590L4-C1590 nm, 130 mW (Typ.) Collimated LED for Olympus BX & IX, 1000 mA
¥74,538
7-10 Days
M617L5-C1 Support Documentation
M617L5-C1617 nm, 484 mW (Typ.) Collimated LED for Olympus BX & IX, 1000 mA
¥65,570
7-10 Days
M625L4-C1 Support Documentation
M625L4-C1625 nm, 630 mW (Typ.) Collimated LED for Olympus BX & IX, 1000 mA
¥72,032
Today
M660L4-C1 Support Documentation
M660L4-C1660 nm, 590 mW (Typ.) Collimated LED for Olympus BX & IX, 1200 mA
¥74,538
7-10 Days
M780L3-C1 Support Documentation
M780L3-C1780 nm, 210 mW (Typ.) Collimated LED for Olympus BX & IX, 800 mA
¥82,512
7-10 Days
M850L3-C1 Support Documentation
M850L3-C1850 nm, 480 mW (Typ.) Collimated LED for Olympus BX & IX, 1200 mA
¥82,512
7-10 Days
M940L3-C1 Support Documentation
M940L3-C1940 nm, 430 mW (Typ.) Collimated LED for Olympus BX & IX, 1000 mA
¥82,512
7-10 Days
MCWHL8-C1 Support Documentation
MCWHL8-C16500 K, 658 mW (Typ.) Collimated LED for Olympus BX & IX, 1400 mA
¥73,105
7-10 Days
Back to Top

Leica製DMI顕微鏡用LED照明、コリメータ付き

  • ビーム径:約37 mm
  • ビーム面積:約1080 mm²
  • ARコーティング付き非球面コリメートレンズ(EFL = 40 mm)
  • 仕様の詳細については「仕様」タブ参照
  • ケーブルの長さ: 2 m
Item #ColoraHousingTotal Beam Powerb
M365L3-C2UV320 mW
M365LP1-C2cUV435 mW
M385L2-C2UV90 mW
M385L3-C2UV450 mW
M385LP1-C2cUV520 mW
M405L4-C2UV310 mW
M405LP1-C2cUV450 mW
M455L4-C2Royal Blue490 mW
M470L5-C2Blue402 mW
M505L4-C2Cyan170 mW
Item #ColoraHousingTotal Beam Powerb
M530L4-C2Green160 mW
M590L4-C2Amber100 mW
M617L5-C2Orange362 mWd
M625L4-C2Red490 mW
M660L4-C2Deep Red400 mW
M780L3-C2IR130 mW
M810L3-C2IR210 mW
M850L3-C2IR330 mW
M940L3-C2IR320 mW
MCWHL8-C2Cold White419 mWe
  • 製造ロットの違いや、温度、電流などの動作パラメータによって、LEDの実際の出力スペクトルは変動します。 出力値や仕様の中心波長は参考データとしてご利用ください。
  • コリメーターパッケージの後。製造工程および温度や電流等の駆動パラメータのバラツキによって、いずれのLEDにおいても合計出力値は変わります。
  • このLEDは出力が高いため、熱放散が向上するようにØ57.0 mmのヒートシンクに取り付けられています。
  • 最大電流での駆動時
  • 25℃で測定
+1 数量 資料 型番 - ユニバーサル規格 定価(税抜) 出荷予定日
M365L3-C2 Support Documentation
M365L3-C2365 nm, 320 mW (Typ.) Collimated LED for Leica DMI, 1000 mA
¥83,871
Today
M365LP1-C2 Support Documentation
M365LP1-C2365 nm, 435 mW (Typ.) Collimated LED for Leica DMI, 1700 mA
¥102,053
Lead Time
M385L2-C2 Support Documentation
M385L2-C2385 nm, 90 mW (Typ.) Collimated LED for Leica DMI, 700 mA
¥67,678
7-10 Days
M385L3-C2 Support Documentation
M385L3-C2375 nm, 450 mW (Typ.) Collimated LED for Leica DMI, 1000 mA
¥86,907
7-10 Days
M385LP1-C2 Support Documentation
M385LP1-C2385 nm, 520 mW (Typ.) Collimated LED for Leica DMI, 1700 mA
¥92,278
7-10 Days
M405L4-C2 Support Documentation
M405L4-C2405 nm, 310 mW (Typ.) Collimated LED for Leica DMI, 1000 mA
¥74,538
Today
M405LP1-C2 Support Documentation
M405LP1-C2405 nm, 450 mW (Typ.) Collimated LED for Leica DMI, 1400 mA
¥92,278
Lead Time
M455L4-C2 Support Documentation
M455L4-C2455 nm, 490 mW (Typ.) Collimated LED for Leica DMI, 1000 mA
¥86,907
Today
M470L5-C2 Support Documentation
M470L5-C2470 nm, 402 mW (Typ.) Collimated LED for Leica DMI, 1000 mA
¥76,388
Today
M505L4-C2 Support Documentation
M505L4-C2505 nm, 170 mW (Typ.) Collimated LED for Leica DMI, 1000 mA
¥86,907
7-10 Days
M530L4-C2 Support Documentation
M530L4-C2530 nm, 160 mW (Typ.) Collimated LED for Leica DMI, 1000 mA
¥86,907
7-10 Days
M590L4-C2 Support Documentation
M590L4-C2590 nm, 100 mW (Typ.) Collimated LED for Leica DMI, 1000 mA
¥74,538
7-10 Days
M617L5-C2 Support Documentation
M617L5-C2617 nm, 362 mW (Typ.) Collimated LED for Leica DMI, 1000 mA
¥65,570
7-10 Days
M625L4-C2 Support Documentation
M625L4-C2625 nm, 490 mW (Typ.) Collimated LED for Leica DMI, 1000 mA
¥72,032
Lead Time
M660L4-C2 Support Documentation
M660L4-C2660 nm, 400 mW (Typ.) Collimated LED for Leica DMI, 1200 mA
¥74,538
7-10 Days
M780L3-C2 Support Documentation
M780L3-C2780 nm, 130 mW (Typ.) Collimated LED for Leica DMI, 800 mA
¥82,512
Lead Time
M810L3-C2 Support Documentation
M810L3-C2810 nm, 210 mW (Typ.) Collimated LED for Leica DMI, 500 mA
¥82,512
7-10 Days
M850L3-C2 Support Documentation
M850L3-C2850 nm, 330 mW (Typ.) Collimated LED for Leica DMI, 1200 mA
¥82,512
Lead Time
M940L3-C2 Support Documentation
M940L3-C2940 nm, 320 mW (Typ.) Collimated LED for Leica DMI, 1000 mA
¥82,512
Lead Time
MCWHL8-C2 Support Documentation
MCWHL8-C26500 K, 419 mW (Typ.) Collimated LED for Leica DMI, 1400 mA
¥73,105
7-10 Days
Back to Top

Zeiss製Axioskop顕微鏡およびExaminer顕微鏡用LED照明、コリメータ付き

  • ビーム径:約44 mm
  • ビーム面積:約1520 mm²
  • Zeiss製AxioskopおよびExaminer顕微鏡のアリ溝に対応
  • ARコーティング付き非球面コリメートレンズ(EFL = 40 mm)
  • 仕様の詳細については「仕様」タブ参照
  • ケーブルの長さ: 2 m
Item #ColoraHousingTotal Beam Powerb
M365L3-C4UV430 mW
M365LP1-C4cUV615 mW
M385L2-C4UV110 mW
M385L3-C4UV570 mW
M385LP1-C4cUV630 mW
M405L4-C4UV410 mW
M405LP1-C4cUV570 mW
M455L4-C4Royal Blue690 mW
M470L5-C4Blue521 mW
M505L4-C4Cyan240 mW
Item #ColoraHousingTotal Beam Powerb
M530L4-C4Green220 mW
M590L4-C4Amber140 mW
M617L5-C4Orange474 mWd
M625L4-C4Red690 mW
M660L4-C4Deep Red570 mW
M780L3-C4IR180 mW
M850L3-C4IR400 mW
M940L3-C4IR380 mW
MCWHL8-C4Cold White596 mWe
  • 製造ロットの違いや、温度、電流などの動作パラメータによって、LEDの実際の出力スペクトルは変動します。 出力値や仕様の中心波長は参考データとしてご利用ください。
  • コリメーターパッケージの後。製造工程および温度や電流等の駆動パラメータのバラツキによって、いずれのLEDにおいても合計出力値は変わります。
  • このLEDは出力が高いため、熱放散が向上するようにØ57.0 mmのヒートシンクに取り付けられています。
  • 最大電流での駆動時
  • 25℃で測定
+1 数量 資料 型番 - ユニバーサル規格 定価(税抜) 出荷予定日
M365L3-C4 Support Documentation
M365L3-C4365 nm, 430 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1000 mA
¥83,871
Lead Time
M365LP1-C4 Support Documentation
M365LP1-C4365 nm, 615 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1700 mA
¥102,053
7-10 Days
M385L2-C4 Support Documentation
M385L2-C4385 nm, 110 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 700 mA
¥67,678
7-10 Days
M385L3-C4 Support Documentation
M385L3-C4385 nm, 570 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1000 mA
¥86,907
7-10 Days
M385LP1-C4 Support Documentation
M385LP1-C4385 nm, 660 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1700 mA
¥92,278
Lead Time
M405L4-C4 Support Documentation
M405L4-C4405 nm, 410 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1000 mA
¥74,538
7-10 Days
M405LP1-C4 Support Documentation
M405LP1-C4405 nm, 580 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1400 mA
¥92,278
Lead Time
M455L4-C4 Support Documentation
M455L4-C4455 nm, 690 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1000 mA
¥86,907
7-10 Days
M470L5-C4 Support Documentation
M470L5-C4470 nm, 521 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1000 mA
¥76,388
7-10 Days
M505L4-C4 Support Documentation
M505L4-C4505 nm, 240 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1000 mA
¥86,907
Lead Time
M530L4-C4 Support Documentation
M530L4-C4530 nm, 220 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1000 mA
¥86,907
7-10 Days
M590L4-C4 Support Documentation
M590L4-C4590 nm, 140 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1000 mA
¥74,538
7-10 Days
M617L5-C4 Support Documentation
M617L5-C4617 nm, 474 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1000 mA
¥65,570
7-10 Days
M625L4-C4 Support Documentation
M625L4-C4625 nm, 690 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1000 mA
¥72,032
7-10 Days
M660L4-C4 Support Documentation
M660L4-C4660 nm, 570 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1200 mA
¥80,072
Lead Time
M780L3-C4 Support Documentation
M780L3-C4780 nm, 180 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 800 mA
¥82,512
7-10 Days
M850L3-C4 Support Documentation
M850L3-C4850 nm, 400 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1200 mA
¥82,512
Lead Time
M940L3-C4 Support Documentation
M940L3-C4940 nm, 380 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1000 mA
¥82,512
Lead Time
MCWHL8-C4 Support Documentation
MCWHL8-C46500 K, 596 mW (Typ.) Collimated LED for Zeiss Axioskop & Examiner, 1400 mA
¥73,105
7-10 Days
Back to Top

Nikon製Eclipse(バヨネットマウント)顕微鏡用LED照明、コリメータ付き

  • ビーム径:約43 mm
  • ビーム面積:約1450 mm²
  • ARコーティング付き非球面コリメートレンズ(EFL = 40 mm)
  • 仕様の詳細については「仕様」タブ参照
  • ケーブルの長さ: 2 m
Item #ColoraHousingTotal Beam Powerb
M365L3-C5UV320 mW
M365LP1-C5cUV435 mW
M385L2-C5UV120 mW
M385L3-C5UV410 mW
M385LP1-C5cUV660 mW
M405L4-C5UV380 mW
M405LP1-C5cUV580 mW
M455L4-C5Royal Blue630 mW
M470L5-C5Blue487 mW
M505L4-C5Cyan220 mW
Item #ColoraHousingTotal Beam Powerb
M530L4-C5Green200 mW
M590L4-C5Amber130 mW
M617L5-C5Orange441 mWd
M625L4-C5Red630 mW
M660L4-C5Deep Red520 mW
M780L3-C5IR170 mW
M850L3-C5IR370 mW
M940L3-C5IR340 mW
MCWHL8-C5Cold White549 mWe
  • 製造ロットの違いや、温度、電流などの動作パラメータによって、LEDの実際の出力スペクトルは変動します。 出力値や仕様の中心波長は参考データとしてご利用ください。
  • コリメーターパッケージの後。製造工程および温度や電流等の駆動パラメータのバラツキによって、いずれのLEDにおいても合計出力値は変わります。
  • このLEDは出力が高いため、熱放散が向上するようにØ57.0 mmのヒートシンクに取り付けられています。
  • 最大電流での駆動時
  • 25℃で測定
+1 数量 資料 型番 - ユニバーサル規格 定価(税抜) 出荷予定日
M365L3-C5 Support Documentation
M365L3-C5365 nm, 320 mW (Typ.) Collimated LED for Nikon Eclipse, 1000 mA
¥89,434
7-10 Days
M365LP1-C5 Support Documentation
M365LP1-C5365 nm, 435 mW (Typ.) Collimated LED for Nikon Eclipse, 1700 mA
¥109,375
7-10 Days
M385L2-C5 Support Documentation
M385L2-C5385 nm, 120 mW (Typ.) Collimated LED for Nikon Eclipse, 700 mA
¥73,694
7-10 Days
M385L3-C5 Support Documentation
M385L3-C5385 nm, 410 mW (Typ.) Collimated LED for Nikon Eclipse, 1000 mA
¥92,441
7-10 Days
M385LP1-C5 Support Documentation
M385LP1-C5385 nm, 630 mW (Typ.) Collimated LED for Nikon Eclipse, 1700 mA
¥99,602
Lead Time
M405L4-C5 Support Documentation
M405L4-C5405 nm, 380 mW (Typ.) Collimated LED for Nikon Eclipse, 1000 mA
¥80,500
7-10 Days
M405LP1-C5 Support Documentation
M405LP1-C5405 nm, 570 mW (Typ.) Collimated LED for Nikon Eclipse, 1400 mA
¥99,602
7-10 Days
M455L4-C5 Support Documentation
M455L4-C5455 nm, 630 mW (Typ.) Collimated LED for Nikon Eclipse, 1000 mA
¥92,441
7-10 Days
M470L5-C5 Support Documentation
M470L5-C5470 nm, 487 mW (Typ.) Collimated LED for Nikon Eclipse, 1000 mA
¥82,986
7-10 Days
M505L4-C5 Support Documentation
M505L4-C5505 nm, 220 mW (Typ.) Collimated LED for Nikon Eclipse, 1000 mA
¥92,441
Lead Time
M530L4-C5 Support Documentation
M530L4-C5530 nm, 200 mW (Typ.) Collimated LED for Nikon Eclipse, 1000 mA
¥92,441
7-10 Days
M590L4-C5 Support Documentation
M590L4-C5590 nm, 130 mW (Typ.) Collimated LED for Nikon Eclipse, 1000 mA
¥80,072
7-10 Days
M617L5-C5 Support Documentation
M617L5-C5617 nm, 441 mW (Typ.) Collimated LED for Nikon Eclipse, 1000 mA
¥68,529
7-10 Days
M625L4-C5 Support Documentation
M625L4-C5625 nm, 630 mW (Typ.) Collimated LED for Nikon Eclipse, 1000 mA
¥79,002
Lead Time
M660L4-C5 Support Documentation
M660L4-C5660 nm, 520 mW (Typ.) Collimated LED for Nikon Eclipse, 1200 mA
¥74,538
7-10 Days
M780L3-C5 Support Documentation
M780L3-C5780 nm, 170 mW (Typ.) Collimated LED for Nikon Eclipse, 800 mA
¥88,860
Lead Time
M850L3-C5 Support Documentation
M850L3-C5850 nm, 370 mW (Typ.) Collimated LED for Nikon Eclipse, 1200 mA
¥88,860
Lead Time
M940L3-C5 Support Documentation
M940L3-C5940 nm, 340 mW (Typ.) Collimated LED for Nikon Eclipse, 1000 mA
¥88,860
Lead Time
MCWHL8-C5 Support Documentation
MCWHL8-C56500 K, 549 mW (Typ.) Collimated LED for Nikon Eclipse, 1400 mA
¥79,156
7-10 Days
Back to Top

マウント付きLED用コネクタ

  • 4ピンメスPico型(M8)レセプタクル
  • マウント付きLEDの電源ケーブル接続用M8 x 1ネジ
  • パネル取付け用M8 x 0.5ネジ、カスタム筐体用
  • 長さ0.5 mのAWG24ケーブル
  • IP 67およびNEMA 6P規格準拠

コネクタCON8ML-4をご使用いただくことで、お手持ちの電源を当社のマウント付きLEDに接続することができます。当社では4ピンオス型M8接続ケーブル(型番CAB-LEDD1)もご用意しております。

PinColorSpecificationPin Assignment
1BrownLED Anode
2WhiteLED Cathode
3BlackEEPROM GND
4BlueEEPROM IO
CON8ML-4
マウント付きLEDの4ピンM8プラグに接続しているCON8ML-4
+1 数量 資料 型番 - ユニバーサル規格 定価(税抜) 出荷予定日
CON8ML-4 Support Documentation
CON8ML-4マウント付きLED用4ピンメス型コネクタ
¥5,006
Today